How to Tell if You Have a Damascus Barrel

By Ra_Dana451 11 May, 2022 Post a Comment

What about a belgian barrel which apart from the many dents has the following marks. Remington gave you the correct information regarding your gun.

Pin On Doubles

The barrel may burst slightly ahead of the chamber crippling the shooters hand or.

. But collectors have found a very few Model 1889s that were sent back to Remington sometime after original shipment and re-barreled with a set of fluid steel tubes those are rare finds. I just dont feel just because its Damascus its unsafe. I re-etched the damascus on an old parker double hammer 10ga last year.

They dont stretch or peel as modern steel does. This gun was intentionally destroyed with a gross overcharge of smokeless powder. Removing a dent from a Damascus barrel will create a weak spot on it.

Removing a dent from a Damascus barrel will create a weak spot on it. Thats probably not the case. But trying to find a gunsmith whos going to open himself up to a future lawsuit because he said a gun was.

Quite often the shotgun will tell you how the barrels are made. Acid etching was often used to accentuate these patterns. If youre in possession of a Damascus barrel shotgun you should go to a competent gunsmith to get a quality check on the barrel.

The process that many of us know is the Crolle Damascus pattern-welded barrels. If you have access to some ferric chloride you could take a cottom swab with some on it and wipe the silver edge with it and it should turn the color of the rest of the Damascus. As to shell pressures most folks dont realize.

When getting it inspected your gunsmith will go through a process of checking a couple points on the gun. Block the barrels and chambers with corks and paint the barrels with the solution several times over 3-4. If you have a pinhole you definitely should not shot black powder in barrel until the barrel is repaired.

The edges of the spiral ribbon were then welded together to form a tube. If you have a gun that is choked. All the blown up Damascus barrels I have seen had chunks blown out of them one or two at the chamber but most at the point where the barrel thins down at about the front of the forearm or where the shooters fingers normally are placed.

If you have a gun that is choked. The barrel may burst slightly ahead of the chamber crippling the shooters hand or forearm. If you clean your Damascus blade you may notice some black residue coming off the blade.

It was pretty cheap and did the job well. That is what brings the contrast of colors in the steel bar. Damascus barrels have a distinctive irregular pattern of short streak-like marks around the barrel.

A thin metal sleeve was wrapped around a mandrel over which the barrel ribbons were wound. Barrel constrictions or choke in most of these side-by-side shotguns were Improved Cylinder Modified or ModifiedFull. Barrel constrictions or choke in most of these side-by-side shotguns were Improved Cylinder Modified or ModifiedFull.

Story 183 by Larry Potterfield Circa 2003 Columbia MO. Imagine a slinky childs toy Basically with a Damascus barrel you are taking that slinky placing it on a metal rod of the proper diameter and heating and hammering the slinky until it is one continuous tube then sliding it off the rod. If your gun has no engraving it very likely doesnt have Damascus barrels.

If you have a defect such as pinholes you should have the gun repaired. Inspect it just as you would any used gun. That does not mean you have a fake.

Drew you know as well as I that Damascus barrel guns shotgun or rifle have always been shot in GB and are still proof tested there. Rust pitting within the barrel. It is relatively easy to remove a dent from a fluid-steel barrel but not so with a Damascus barrel.

Damascus barrels are identified from the beautiful and striking patterns often produced by the alternating layers of iron and steel. D under a crown PV under a lion ELG in a circle under a crown. Wall thickness of the barrel.

A gun in this condition is a wall hanger. Yours probably has their Compressed Fluid. Such a charge would have destroyed any modern shotgun.

Then pulled and rinsed with water and baking soda. But modern extruded steel tube is much much better. 22 Oct 14 2012.

A man doesnt have many chances to help establish facts. IIRC it took about 1 12 minutes total time. Why is There a Huge Price Difference for Damascus.

The warning is not to never shot a damascus barrel the warning is if you suspect defects have them checked and repaired. A chap named Wabbitbosher is an expert on this. Remington 1900 12 gauge side-by-side with Damascus barrels.

It normally took seven feet of rod to create one foot of barrel. Damascus barrels are weaker than modern barrels and are not designed for the high gas pressures created by modern ammunition. If you have a Damascus barrel gun dont shoot it.

Needless to say those arent a 300 Mossberg or Rem. A gun in this condition is a wall hanger. An acquaintance of mine sent a Stephen Grant double in 500 BPE with Damascus barrels back to Birmingham UK and had it proofed for NFB loads.

I used the circuit board etchant from radio shack. That is likely residue from the acid etching. Basically you should rub down the areas to be browned with very fine steel wool then look on the internet for suppliers of browning solutions.

If it says twist or laminated or damascus then it is one of the types generally called damascus. You may be thinking to yourself that this must be the print coming off. If you have a Damascus barrel gun dont shoot it.

I believe your blade is Damascus. Damascus barrels have a distinctive irregular pattern of short streak-like marks around the barrel. These are acids with maybe an additive or two.

The threads were connected heated and hammer-welded the mandrel was removed and a barrel was formed. For re-sale purposes the British and German firearms are sent back to England and Germany and re-proofed. In the Model 1889 only the higher grades engraved had Damascus which was considered a classy and valuable feature.

It is relatively easy to remove a dent from a fluid-steel barrel but not so with a Damascus barrel. Be sure to wipe if off with water when done and oil it Terry. How can you tell if a rust covered barrel is a damascus one.

New Damascus barrels are made from powdered steel that gives it the appearance of Damascus steel. Long story short if a gun wasnt made by one of the high quality gunsmiths in the US or Europe and it was made after WWI it aint real and even then you dont want to fire any true Damascus barreled guns because its unsafe for you and the. I let the barrels sit in the stuff for about 30 sec.

Damascus Barrels - Rumors Facts.

Pin On Doubles

Gunsmithing How To Rust Blue Damascus Or Twist Steel Barrels Steel Barrel Barrel Gunsmithing